Ciao, 2.5.x means 2.5.0 or 2.5.1?webrab wrote: ↑Mon Feb 20, 2017 8:44 am Hi,
since I have updated the FW to 2.5.x I cannot see PowerBalance in TrainingPeaks anymore.
I have tried it with 2 different Quarq PMs. Not tested it yet with my SRM PM on my road-bike.
If I'm using the data-field Leistungs-Balance on the PC8, the value is overtime 50-50%
/ralf
PC8 firmware: news - novità
Re: PC8 firmware: news - novità
Ing. Simone Stilli
Responsabile SRM Italia - Software Developer
Responsabile SRM Italia - Software Developer
Re: PC8 firmware: news - novità
Version 2.5.1 installed no problems. Test ride later this day!
ciao
edi
ciao
edi
-
- Posts: 14
- Joined: Mon Feb 13, 2017 7:56 am
Re: PC8 firmware: news - novità
Today i check the connection between the PC8 FW 2.5.1 and a Rotor Inpower Crank.
The connection works and the crank size setting too. The calibration works sometimes.
The most wonderment is the extremely high calibration value of 65457, by comparison my Garmin Edge 820 have the calibration value 80.
With the calibration value of 65457 the PC8 shows some power output, but i don't now how correct they are and between the first paddling an the first power values is a time gap between 5-10 sek. After I have stopped it shows me over the same duration still values.
The connection works and the crank size setting too. The calibration works sometimes.
The most wonderment is the extremely high calibration value of 65457, by comparison my Garmin Edge 820 have the calibration value 80.
With the calibration value of 65457 the PC8 shows some power output, but i don't now how correct they are and between the first paddling an the first power values is a time gap between 5-10 sek. After I have stopped it shows me over the same duration still values.
You do not have the required permissions to view the files attached to this post.
Re: PC8 firmware: news - novità
I've encountered two problems with 2.5.0
1) If I do a zero offset mid ride the power will display as zero until I cycle through all screens
2) Satellite pickups seem slower
1) If I do a zero offset mid ride the power will display as zero until I cycle through all screens
2) Satellite pickups seem slower
Re: PC8 firmware: news - novità
Since 2.5.1 is out, please refer to this.
Ing. Simone Stilli
Responsabile SRM Italia - Software Developer
Responsabile SRM Italia - Software Developer
Re: PC8 firmware: news - novità
Super!
Ing. Simone Stilli
Responsabile SRM Italia - Software Developer
Responsabile SRM Italia - Software Developer
Re: PC8 firmware: news - novità
We will check. Thanks.SeñorStark wrote: ↑Mon Feb 20, 2017 9:50 am Today i check the connection between the PC8 FW 2.5.1 and a Rotor Inpower Crank.
The connection works and the crank size setting too. The calibration works sometimes.
The most wonderment is the extremely high calibration value of 65457, by comparison my Garmin Edge 820 have the calibration value 80.
With the calibration value of 65457 the PC8 shows some power output, but i don't now how correct they are and between the first paddling an the first power values is a time gap between 5-10 sek. After I have stopped it shows me over the same duration still values.
Ing. Simone Stilli
Responsabile SRM Italia - Software Developer
Responsabile SRM Italia - Software Developer
Re: PC8 firmware - feature request
Thanks for your feedback. Regarding the iLevels we need to plan since the training zones are into the PC8 too and right now we can menage max 7.OlyEST wrote: ↑Sun Feb 19, 2017 10:05 pm I would like to request the option when choosing power zones/level on PC, or in SRMX software, to choose Coggan iLevels.
Seems this would benefit both coaches and self-coached athletes alike.
More information on iLevels can be found here:
http://home.trainingpeaks.com/blog/arti ... ls-in-wko4
and here:
https://www.youtube.com/watch?v=wTYE1VZewgc
thanks,
The request is under discussion.
Ing. Simone Stilli
Responsabile SRM Italia - Software Developer
Responsabile SRM Italia - Software Developer
Re: PC8 firmware: news - novità
Ho notato che lasciando fare il rilevamento della velocità al gps, rispetto al vecchio firmware(pre-beta tester) la velocità visualizzata è spesso sottostimata..
mentre prima accadeva solo sul strade molto molto coperte adesso la velocità viene sottostimata anche in strade più normali( con alberi dalle parti ma nn coperte)..
il rilevamento dei km totali invece è esatto(confrontato con pc7+sensore ant+)
mentre prima accadeva solo sul strade molto molto coperte adesso la velocità viene sottostimata anche in strade più normali( con alberi dalle parti ma nn coperte)..
il rilevamento dei km totali invece è esatto(confrontato con pc7+sensore ant+)
Re: PC8 firmware: news - novità
HI Simone
In the new firmware 2.5.x I also found the problem on the GPS
PC8 display Charging power was 70-80%,can not reach 100%
At 2.17 23:33:28 start riding 24 minutes 23 seconds paused. when I started a new ride and found no power meter,I tried to connect the power meter many times, but I failed to connect the power meter.
(Note:My SRM Power meter starts for about 140 hours)
These tow days I have several times with PC8 and Garmin equipment try to connect the power meter, the same connection is not on the power meter
https://youtu.be/RVOBA9Y4GpM
PC8 connection power meter
https://youtu.be/0DEpZBzYnUA
Garmin device connection power meter
In the new firmware 2.5.x I also found the problem on the GPS
PC8 display Charging power was 70-80%,can not reach 100%
At 2.17 23:33:28 start riding 24 minutes 23 seconds paused. when I started a new ride and found no power meter,I tried to connect the power meter many times, but I failed to connect the power meter.
(Note:My SRM Power meter starts for about 140 hours)
These tow days I have several times with PC8 and Garmin equipment try to connect the power meter, the same connection is not on the power meter
https://youtu.be/RVOBA9Y4GpM
PC8 connection power meter
https://youtu.be/0DEpZBzYnUA
Garmin device connection power meter
You do not have the required permissions to view the files attached to this post.